How To Clean Drywall Dust Off Laminate Floors

Download Article

Download Article

Drywall is used to form the inside walls of buildings and houses. Information technology requires sanding, which results in a large amount of grit. Demolition of old drywall also generates a considerable amount. Drywall grit is very fine and pervasive, with a consistency shut to powder. Because of this, it can quickly and easily spread throughout your home. You'll need to be vigilant to forbid this, starting with preventative measures earlier the task begins.

1. 1

   Sweep starting time. ^[one] Start from the outside and piece of work your mode to the center of the room. Have your time and sweep with gentle strokes to avoid stirring upwards the dust more than than you take to. Use a dustpan to scoop up the dust pile and place it in a trash purse.^[2] Tie the bag upward immediately to seal the dust in. If you are working with a significant amount of dusk, there are products you lot tin purchase that will help the dust cling to the floor. This will make information technology easier to sweep up.

   • You can buy sweeping compound products at any home improvement shop. They are usually sold in bags or buckets. The compound itself has a grit/sawdust-like consistency.
   • To employ, milk shake the compound over the floor where y'all want to sweep. Information technology holds the dust down to the floor and then that you can sweep information technology up more hands.
   • Many of the products crave 24 hours to settle over the dust earlier you can sweep it, and then read the instructions carefully.

2. 2

   Vacuum the floors. ^[3] The well-nigh effective vacuum for this job is a wet/dry vacuum, also known as a Shopvac.^[4] If you lot don't own 1 already, many dwelling improvement stores rent them out. Use vacuum bags that are made specifically for collecting dry wall dust. For the effectively particles, use a HEPA filter.

   • The filters can get chock-full so, if possible, use a filter that can be washed and reused.
   • It's also wise to have a back-up filter on hand, just in case.
   • Use a hose attachment to get into hard-to-attain areas where drywall dust could collect.^[5]

   Advert

3. iii

   Wipe everything down with a clammy microfiber material. ^[6] Fill a bucket with cool water. Dip the cloth in the water and wring it out well – a soaking wet material can damage fresh drywall. Start at the meridian of the walls and work your way downward. You'll need to rinse and wring out the cloth often.^[7]

   • Change the water in the saucepan as soon equally it gets cloudy.
   • After the walls, wipe down every horizontal surface in the room. This includes baseboards, light fixtures, outlet covers, etc.^[8]

4. 4

   Vacuum a second time. Insert a castor attachment for the second pass. Brush attachments help to get in the nooks and crannies. It likewise has a hose fastened that will allow yous to vacuum the walls. Commencement at the meridian and vacuum your way down to the bottom.

   • After the walls, vacuum the flooring again.
   • You'll will probably need to vacuum in the corners of the room and over the joints twice.

5. 5

   Spot clean with a damp microfiber cloth. Cheque the room and wipe up any lingering dust that you lot see. Run the cloth over the baseboards and window ledges one more time. If you want to be extra vigilant, damp mop the floor equally a final step.^[9]

   • Brand sure you're using clean water in the bucket, fifty-fifty for the concluding wipe down.

Advertisement

1. ane

   Block off all vents and openings with plastic sheeting. ^[ten] Heavy-duty plastic sheeting helps to minimize how much grit gets dispersed through the air. Cover all the openings throughout your habitation, such equally doorways and windows, with it. For all-time results, hang the sheeting from floor to ceiling.

   • Cover all of the air vents and ductwork.
   • Secure the plastic sheeting with masking tape.

2. 2

   Cover the flooring and protect the furniture. ^[eleven] Motion equally much furniture out of the style every bit you can. Cover what can't be moved with plastic sheeting, especially upholstered furniture, since the grit can work itself into the cloth. Secure the sheeting in place with bungee cords.^[12]

   • Place plastic sheeting over the entire floor of your piece of work area.
   • If you have carpet in the remainder of the house, consider covering the floors in every room with self-adhesive plastic lining.

3. 3

   Plow off the central heat and air apportionment. ^[thirteen] Leaving the system on will outcome in drywall dust getting into it, which volition then spread throughout your abode. Fifty-fifty though you lot're roofing all of the air ducts with plastic sheeting earlier you begin, it is still beneficial to plough off the circulation organisation.

   • Exist sure to leave the apportionment system off until you've completed your chore and cleaned up the dust later.
   • Bank check your organisation'southward air filter frequently in the weeks following the sanding. Y'all volition probably need to replace it before long after.^[xiv]

4. 4

   Identify box fans in the windows. ^[fifteen] Using box fans will help continue the room you are working in ventilated. Open the windows and place the box fans in them.^[16] Be sure to position the box fans so that air blows out of the room, non into it. Employ plastic sheeting to seal off the area effectually the fans and window frames. Duct tape the plastic in place.^[17]

   • If whatever of the windows have air workout units in them, remove them from the room. They get chock-full with grit easily.
   • Use the box fans on a low setting, which will cause the least air disturbance. Setting them on high will suck out a lot of the grit, only it will likewise increment the amount that's moving through the air.

5. five

   Remove the door and window screens. ^[18] This will allow the grit to move freely from inside to outside. It too improves the air apportionment in the area. Not removing the screens volition trap a lot of the dust in the room. You'll also have to remove drywall dust from the screens after you've finished sanding.

6. 6

   Wear gloves and a face mask. Put on a face up mask that covers your olfactory organ and mouth so y'all don't exhale in any of the drywall dust. Put on work gloves to prevent grit from sticking on your hands while you lot're cleaning.^[19]

   • Practice non remove your face mask during cleaning. Animate in drywall dust can cause serious health problems.^[20]

Advertisement

1. one

   Take breaks to make clean. ^[21] Because the grit is and then pervasive, remove as much as you can before it has a risk to build up. It'due south non ideal, but cleaning frequently throughout the project can assistance you reduce a lot of dust. How often you finish to clean is upwards to you, but at minimum you lot demand to clean at least in one case per mean solar day.

   • Wipe downward surfaces with a microfiber towel or a damp material. Employ a vacuum cleaner to get up the dust on the flooring.

2. 2

   Limit access to the work area. Dry wall dust is such a fine pulverization that simply walking around in the work area stirs information technology upwardly. Fifty-fifty after y'all've stopped sanding, the grit hangs in the air for quite a while. Walking through pushes it effectually in the air.

   • The more people walk through the area, the faster the dust will spread.
   • Restrict the work area to only others working on the project.^[22]

3. three

   Designate one entryway. ^[23] It's going to be difficult not to rails dust in and out of the work area, and so choose one archway and seal the other entryways off. Lay a mat in front end of the entrance. A mat isn't going to make a huge difference, but at the very least you lot tin can reduce tracking dust past wiping the soles of your shoes off before leaving the area.

   • If you're doing piece of work in your own home, removing your shoes and leaving them backside volition assist.

Advertisement

Add New Question

• Question

  Are there people who will clean this for me?

  

  If you hired people to practice the drywall, they should clean the mess. Otherwise, you can hire a cleaning service.

• Question

  How do I remove the white dust from sail rock on a tile floor?

  

  Outset y'all can vacuum it then you accept to mop information technology upwardly until it is clean.

• Question

  How practice I mop the floor without causing drywall grit to get into the air?

  

  By mopping with a wet mop, you lot will pick upwards the drywall dust and it will not bladder into the air. Rinse the mop regularly to go on it clean and change the h2o in the bucket when information technology gets murky.

Enquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Advertisement

Video

About This Article

Article Summary 10

To make clean drywall dust, start by sweeping upward any grit on the floors, using brusk, gentle strokes and so you don't stir it upward into the air. Yous may want to apply a sweeping chemical compound to the floor so the dust sticks and is easier to sweep up. Next, when you're finished sweeping, vacuum the floors with a wet and dry vacuum that has a HEPA filter. And so, wipe down all surfaces with a damp microfiber fabric before vacuuming the floors again. Finally, spot clean whatsoever lingering grit with the damp fabric. To learn how to prevent drywall grit from accumulating during your project, go along reading!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 277,480 times.

Did this commodity help you?

Source: https://www.wikihow.com/Clean-Drywall-Dust

Share this post